Successful relay cross reference chart for High-Risk Applications
Reliable relay cross reference chart Designs for Industrial and Industrial Applications
CHINA – ?¡ãAny Electronics?¡À proudly presents their entire variety of relay cross reference chart . They provide a complete set of relay cross reference chart solutions and other interrelated goods. These units are seen in unique applications for instance commercial applications, industrial control circuits as well as OEM Panels. These devices come with outstanding precision and repeatability. The normal relay cross reference chart that happen to be designed lately require incredibly tiny panel space.
bosch relay cross reference chart omron relay cross reference chart ac delco relay cross reference chart
There was an error connecting to the Amazon web service, or no results were found for your query.
Joshwa asked A/C on my 2001 Nissan Frontier works intermittently?
The A/C on my truck works intermittently. When the car has been in the sun for awhile it blows cold air for a little then the air goes hot. After awhile it turns hot again.
And got the following answer:
AIR CONDITIONER PROBLEM: INTERMITTENT COOLING An A/C system that blows cold air for awhile then warm air is probably freezing up. This can be caused by air and moisture in the system that allows ice to form and block the orifice tube. Evacuating the system with a vacuum pump will purge it of unwanted air and moisture. Evacuation should be done with a vacuum pump that is capable of achieving and holding a high vacuum (29 inches) for at least 30 to 45 minutes. For best performance, an A/C system should contain less than 2% air by weight. For every 1% increase in the amount of air that displaces refrigerant in the system, there will be a corresponding drop of about one degree in cooling performance. More than 6% air can cause a very noticeable drop in cooling performance, and possibly cause evaporator freeze-up. Air can get inside a system through leaks, by not evacuating the system prior to recharging it, and/or by recharging the system with refrigerant that is contaminated with air. Recovery equipment can suck air into the recycling tank if an A/C system contains air or if the system has a leak. For this reason, the refrigerant recovery tank on recycling equipment must be checked and purged daily. On some equipment, this is done automatically. But on equipment that lacks an automatic purge cycle, tank pressure and temperature has to be measured and compared to a static pressure reference chart. Some refrigerant identifier equipment can detect air in the system as well as other contaminants. An identifier should be used to check the refrigerant before the system is serviced to prevent cross-contamination of recovery and recycling equipment. Possible causes of intermittent cooling in a manual A/C system that might be caused by an electrical problem include: Faulty low pressure cutout switch. This switch prevents the compressor from running if the refrigerant level is low. If the cutout switch is not reading correctly, it can prevent the compressor from coming on. Faulty compressor clutch. The magnetic clutch on the compressor requires full battery voltage to engage. If the voltage to the clutch is low, or the clutch coils have too much resistance, or the air gap in the clutch is too great, the clutch may not engage to drive the compressor. Faulty compressor clutch relay. Check to see if the relay is receiving voltage when the A/C is turned on. Also check the relay wiring and ground connections. If bypassing the relay with a jumper wire or routing battery voltage directly to the compressor clutch makes the A/C work, the relay is probably bad. Faulty A/C control switch. The switch may be worn and not making good contact when it is turned on. Some possible causes of intermittent cooling (or no cooling) on automatic A/C systems include all of the above, plus: A problem in the control module or control head (this usually requires using a dealer scan tool to read fault codes and perform self-diagnostics). A bad temperature sensor (an ambient air temperature sensor, interior air temperature sensor, evaporator temperature sensor, or sunload sensor). Again, a factory scan tool is usually required to perform diagnostics on the system. i copied this off the web. if u are going to trouble shoot yourself, u might want to see if the compressor clutch is engaging when the ac blows hot. u might have an electrical issue that is shutting compressor down such as a bad pressure switch (on top of drier). good luck. let us know what the problem turns out to be.
The relay cross reference chart perform particularly well with various applications which can be specific to power distribution and protection. The relays include wide adjustment ranges with a scale which is simple to read either in 3 or 4 digits as outlined by the model. These relay cross reference chart assistance in growing the flexibility from the applications, minimize the all round energy and upkeep fees. You’ll find relays which are made use of for common purposes which come in reliable designs with swift replacement alternatives. And you will find models that are employed for industrial applications and heavier duty applications that work on significant loads. These solutions are created to meet the lifetime industrial manage requires in the applications.
Their most recent solutions will be the Time counter, Timer Delay, relay cross reference chart, Fast Connect Couplings, Electronic Motor Couplings, Aluminum Couplings, Morse Couplings and a variety of other people. The web page provides a detailed description of every single model in several categories of relay cross reference chart couplings and sensors. These items are exceptionally valuable for high-risk applications. The relay cross reference chart are also available with features like several timing ranges and functions. The enterprise is at present looking for agents and dealers who can market and sell their factory produced merchandise. They may be always on a lookout for establishing new and more reliable goods determined by the requirements and specifications on the sector.